Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
Name übersetzen
NORM herausgegeben am 1.9.2017
Bezeichnung normen: ASTM A599/A599M-07(2017)
Ausgabedatum normen: 1.9.2017
SKU: NS-796619
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. The material shall conform to specified chemical composition requirements. The mechanical property requirements for structural steel, high-strength low-alloy steel with and without improved formability, commercial steel, and deep drawing steel are presented in details. The weight [mass] of coating shall conform to specified requirements fit for individual coating designations. The typical methods for determination of tin coating weights are described.
Keywords:
ICS Number Code 77.140.50 (Flat steel products and semi-products)
1. Scope | |||||||||||||||||||||||||||
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1. TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass] Note 1: Listed below are the commonly produced coating weights
[mass] upon agreement between the producer and the purchaser. Other
combinations of coatings may be specified and the appropriate
minimum average test valuesA apply.
1.1.1 Electrolytic tin-coated sheet is
customarily available as commercial steel (CS); drawing steel (DS);
deep drawing steel (DDS); extra deep drawing steel (EDDS), and
structural steel (SS). The tin coating is available as unmelted or
melted.
1.2 Limitations—This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M]. 1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
|||||||||||||||||||||||||||
2. Referenced Documents | |||||||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.