Vorsicht!

In Ihrem Browser ist die Javascript-Aktivierung nicht erlaubt. Einige Funktionen mögen nicht richtig funktionieren. Für vollständige Funktionalität des Internet-Geschäfts empfehlen wir Javascript zu aktivieren. Siehe hier Instruktion, wie man im Ihren Web-Browser JavaScript aktiviert.

Angezeigte Währung: €

Preisanzeige: ohne MWS

Ergänzende Informationen

ASTM B306-20

Standard Specification for Copper Drainage Tube (DWV)

Name übersetzen

NORM herausgegeben am 1.6.2020

Sprache
Realisierung	PDF - sofortiges Download - 66.40 € PDF + redline - sofort - 79.70 € Gedruckt - 66.40 € Gedruckt + redline - 79.70 €
Zugänglichkeit	AUF LAGER
Preis	66.40 € ohne MWS
66.40 €

Informationen über die Norm:

Bezeichnung normen: ASTM B306-20
Ausgabedatum normen: 1.6.2020
SKU: NS-999917
Zahl der Seiten: 7
Gewicht ca.: 21 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM

Drucken

Einem Bekannten abschicken

Anfrage

Kategorie - ähnliche Normen:

Non-ferrous metal pipes

Die Annotation des Normtextes ASTM B306-20 :

This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping. The tube shall be manufactured by such hot- or cold-working process as to produce a homogeneous uniform wrought structure in the finished product. The tube shall be cold drawn to the specified finished size, wall thickness, tensile strength, and Rockwell hardness. The tube shall be subjected to chemical analysis, Eddy-current test, and pneumatic test. Instead of sampling in accordance with Practice E 255, the manufacturer shall have the option of sampling at the time casting are poured or from the semifinished product, subject to the conditions set in the specification.

Keywords:

drainage tube, sanitary tube, seamless copper tube, vent tube, waste tube,, ICS Number Code 23.040.15 (Non-ferrous metal pipes)

Ergänzende Informationen

Significance and Use

17.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29:

Property	Rounded Unit for Observed or Calculated Value

Chemical composition	nearest unit in the last right-hand place of
Hardness	figures of the specified limit

Tensile strength	nearest ksi (5 MPa)

1. Scope

1.1 This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping.

Note 1: Fittings used for soldered or brazed connections in drainage, waste, or vent systems are described in ASME Standards B16.23 and B16.29 and CSA Standard B158.1.

Note 2: The assembly of copper drainage, waste, and vent systems by soldering is described in Practice B828.

Note 3: Solders for joining copper drainage, waste, or vent systems are described in Specification B32. The requirement for acceptable fluxes for these systems are described in Specification B813.

1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following hazard statement pertains only to the test method(s) described in this specification:

1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
B32-20	Standard Specification for Solder Metal
E243-18	Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
B900-16(2022)	Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
B828-23	Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings
B813-16	Standard Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
B16.23	Cast Copper Alloy Solder Joint Drainage Fittings--DWV
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
B601-18a	Standard Classification for Temper Designations for Copper and Copper Alloys´Wrought and Cast (Includes all amendments and changes 10/24/2018).
B16.29	Wrought Copper and Copper Alloy Solder Joint Drainage Fittings--DWV

Empfehlungen:

Aktualisierung der technischen Normen

Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.

Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.

Hier können Sie Ihre Cookie-Einstellungen nach Ihren Wünschen anpassen.

Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können.