Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Guide for Determining Mass Per Unit Area of Electrodeposited and Related Coatings by Gravimetric and Other Chemical Analysis Procedures
Automatische name übersetzung:
Standard-Leitfaden zur Ermittlung der flächenbezogenen Masse von Galvanische und verwandten Beschichtungen durch gravimetrische und andere chemische Analyseverfahren
NORM herausgegeben am 1.11.2010
Bezeichnung normen: ASTM B767-88(2010)
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.11.2010
SKU: NS-8032
Zahl der Seiten: 6
Gewicht ca.: 18 g (0.04 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
Acceptance criteria/testing--coatings, Aluminum coatings, Anodic coatings, Average mass per unit area, Brass electrodeposition, Cadmium metals (coating/plating), Chemical analysis, Chromate coatings, Chromium electroplating, Coating thickness, Density--metallic coatings, Electrodeposited coatings, Electrodeposited Cu coatings, Electrodeposited gold coatings, Gravimetric determination, Lead metals/alloys, Lead-tin alloys/coatings, Linear changes/linearity, Mass per unit area
Significance and Use | ||||||||||
The thickness of a coating is critical to its performance and is specified in many specifications calling for coatings. These procedures are used for acceptance testing and appear in a few specifications. Coating thickness instruments are often calibrated with thickness standards that are based on mass and area measurements. The average thickness of a coating on the measured area can be calculated from its mass per unit area only if the density of the coating material is known. |
||||||||||
1. Scope | ||||||||||
1.1 This guide outlines a general method for determining the mass per unit area of electrodeposited, electroless, mechanically-deposited, vacuum-deposited, anodicoxide, and chemical conversion coatings by gravimetric and other chemical analysis procedures. 1.2 This guide determines the average mass per unit area over a measured area. 1.3 The stripping methods cited are described in specifications or in the open literature or have been used routinely by at least one laboratory. 1.4 The procedures outlined can be used for many coating-substrate combinations. They cannot be used where the coating cannot be separated from the substrate by chemical or physical means as would be the case if white brass were plated with yellow brass. 1.5 In principle, these procedures can be used to measure very thin coatings or to measure coatings over small areas, but not thin coatings over small areas. The limits depend on the required accuracy. For example, 2.5 mg/cm2 of coating might require 2.5 mg of coating covering 1 cm2, but 0.1 mg/cm2 of coating would require 25 cm2 to obtain 2.5 mg of coating. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||
2. Referenced Documents | ||||||||||
|
Historisch
1.12.2013
Historisch
1.10.2011
Historisch
1.4.2010
Historisch
1.5.2014
Historisch
1.12.2013
Historisch
1.8.2008
Bereitstellung von aktuellen Informationen über legislative Vorschriften in der Sammlung der Gesetze bis zum Jahr 1945.
Aktualisierung 2x pro Monat!
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.