Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Specification for Portland Cement
Name übersetzen
NORM herausgegeben am 1.7.2022
Bezeichnung normen: ASTM C150/C150M-22
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.7.2022
SKU: NS-1068713
Zahl der Seiten: 9
Gewicht ca.: 27 g (0.06 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
hydraulic cement, portland cement, specification,, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
1.1?This specification covers ten types of portland cement, as follows (see Note 2): 1.1.1?Type IFor general use, when the special properties specified for any other type are not required. 1.1.2?Type IAAir-entraining cement for the same uses as Type I, where air-entrainment is desired. 1.1.3?Type IIFor general use, more especially when moderate sulfate resistance is desired. 1.1.4?Type IIAAir-entraining cement for the same uses as Type II, where air-entrainment is desired. 1.1.5?Type II(MH)For general use, more especially when moderate heat of hydration and moderate sulfate resistance are desired. 1.1.6?Type II(MH)AAir-entraining cement for the same uses as Type II(MH), where air-entrainment is desired. 1.1.7?Type IIIFor use when high early strength is desired. 1.1.8?Type IIIAAir-entraining cement for the same use as Type III, where air-entrainment is desired. 1.1.9?Type IVFor use when a low heat of hydration is desired. 1.1.10?Type VFor use when high sulfate resistance is desired. Note 1:?Some cements are designated with a combined type
classification, such as Type I/II, indicating that the cement meets
the requirements of the indicated types and is being offered as
suitable for use when either type is desired.
Note 2:?Cement conforming to the requirements for all types
are not carried in stock in some areas. In advance of specifying
the use of cement other than Type I, determine whether the proposed
type of cement is or can be made available.
1.2?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice. 1.3?The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-21 (Zahl der Positionen: 2 206 478)
© Copyright 2024 NORMSERVIS s.r.o.