Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes
Automatische name übersetzung:
Standardtestverfahren für lineare Schrumpfung und Wärmeausdehnungskoeffizient eines Chemikalienmörtel, Fugenmörtel, Monolithic Auftragungen, und Polymerbeton
NORM herausgegeben am 1.8.2012
Bezeichnung normen: ASTM C531-00(2012)
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.8.2012
SKU: NS-13882
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
brick mortars, grouts, linear shrinkage, monolithic surfacings, mortars, polymer concretes, thermal expansion, tile grouts, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Significance and Use | ||||||
4.1 This test method offers a means of comparing the relative linear shrinkage and coefficient of thermal expansion. 4.1.1 The material to be tested is placed in the mold in a fluid or plastic state. As the material makes a transition to a solid state, it adheres to and captures the end studs. 4.1.2 The linear shrinkage measured is the change in length that occurs after the material is rigid enough and strong enough to move the studs. 4.2 This test method can be used for research purposes to provide information on linear changes taking place in the test materials. Other dimensional changes may occur that do not manifest themselves as changes in length. |
||||||
1. Scope | ||||||
1.1 This test method covers the measurement of the linear shrinkage during setting and curing and the coefficient of thermal expansion of chemical-resistant mortars, grouts, monolithic surfacings, and polymer concretes. 1.2 A bar of square cross-section is cast to a prescribed length in a mold that holds measuring studs that are captured in the ends of the finished casting. 1.2.1 The change in length after curing is measured and used to calculate shrinkage. 1.2.2 The change in length at a
specific elevated temperature is measured and used to calculate the
coefficient of thermal expansion.
1.3 This test method is limited to materials with aggregate size of 0.25 in. (6 mm) or less. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
2. Referenced Documents | ||||||
|
Historisch
1.10.2010
Historisch
1.3.2012
Historisch
15.5.2010
Historisch
15.12.2012
Historisch
15.12.2010
Historisch
1.8.2013
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-23 (Zahl der Positionen: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.