Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM D2557-98(2017)
Standard Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from -267.8 to -55°C (-450 to -67°F)
Name übersetzen
NORM herausgegeben am 1.11.2017
Informationen über die Norm:
Bezeichnung normen: ASTM D2557-98(2017)
Ausgabedatum normen: 1.11.2017
SKU: NS-800216
Zahl der Seiten: 4
Gewicht ca.: 12 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM D2557-98(2017) :
Keywords:
adhesive, metals, subzero temperature range, tensile shear strength,, ICS Number Code 83.180 (Adhesives)
Ergänzende Informationen
| Significance and Use | ||||||||||||
|
4.1 This test method may be used as an accelerated screening test for assessing the strength properties of adhesives and adhesive joints at subzero temperatures. This test method may also be used to determine the effects of various surface preparations, substrates, or adhesive systems on the durability of the adhesive joints at subzero temperatures. 4.2 Tensile shear strengths of various adhesives, surface preparations, and substrates may be compared by using this test method for uniform sets of conditions. To assess the overall tensile shear strength of a given adhesive, surface preparation, and substrate should be tested under a range of stress and temperatures. For a specific end use, the needed strength properties using only one set of test conditions may be obtained. 4.3 The misuse of strength values obtained from this test method as design-allowable stress values for structural joints could lead to product failure, property damage, and human injury. 4.3.1 The apparent shear strength of an adhesive obtained from a given small single-lap specimen may differ from that obtained from a joint made with different adherends or by a different bonding process. The normal variation of temperature and moisture in the service environment causes the adherends and the adhesive to swell or shrink. The adherends and adhesive are likely to have different thermal and moisture coefficients of expansion. Even in small specimens, short-term environment changes can induce internal stresses of chemical changes in the adhesive that permanently affect the apparent strength and other properties of the adhesive. 4.3.2 The problem of predicting joint behavior in a changing environment is even more difficult if a different type of adherend is used in a larger structural joint than was used in the small specimen. 4.3.3 The apparent shear strength measured with a single-lap specimen is not suitable for determining design-allowable stresses for designing structural joints that differ in any manner from the joints tested without thorough analysis and understanding of the joint and adhesive behaviors. 4.3.4 Single-lap tests may be used for comparing and selecting adhesives or bonding processes for susceptibility to fatigue and environmental changes, but such comparisons must be made with great caution since different adhesives may respond differently in different joints. See Guide D4896 for further discussion of the concepts relative to interpretation of adhesive-bonded single-lap-joints. |
||||||||||||
| 1. Scope | ||||||||||||
|
1.1 This test method covers the determination of the comparative shear strength of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing at extreme subzero temperatures. 1.2 This test method is applicable to the temperature range from -267.8 to -55°C (-450 to -67°F). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Empfehlungen:
Aktualisierung der Gesetze
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Vorschriften verwenden?
Wir bieten Ihnen Lösungen, damit Sie immer nur die gültigen (aktuellen) legislativen Vorschriften verwenden könnten.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
