Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Methods for Lead in Water
Automatische name übersetzung:
Standard-Prüfverfahren für Blei im Wasser
NORM herausgegeben am 1.10.2008
Bezeichnung normen: ASTM D3559-08
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.10.2008
SKU: NS-24057
Zahl der Seiten: 17
Gewicht ca.: 51 g (0.11 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
atomic absorption, chelation-extraction, graphite furnace spectrophotometry, lead, voltammetry, Atomic absorption, Chelation-extraction, Differential pulse anodic stripping voltammetry, Graphite furnace atomic absorption spectrometry (GFAAS), Inorganic compounds--water, Lead content, Lead screening testing, Polarographic methods, Spectrophotometry--atomic absorption (water/wastewater), Voltammetry--differential pulse anodic stripping
Significance and Use | ||||||||||||||||||||||||||||||||||||||||
The test for lead is necessary because it is a toxicant and because there is a limit specified for lead in potable water in the National Interim Primary Drinking Water Regulations. This test serves to determine whether the lead content of potable water is above or below the acceptable limit. |
||||||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||||||
1.1 These test methods cover the
determination of dissolved and total recoverable lead in water and
waste water by atomic-absorption spectrophotometry and differential
pulse anodic stripping voltammetry. Four test methods are included
as follows:
1.2 Test Method B can be used to determine lead in brines. Test Method D has been used successfully with reagent water, lake water, well water, filtered tap water, condensate from a medium Btu coal gasification process, waste treatment plant effluent, and a production plant process water. 1.3 It is the user's responsibility to ensure the validity of these test methods for waters of untested matrices. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see 10.4.1, Note 2, 11.2, 11.3, 21.7, 21.8, 21.11, 23.7, 23.10, 32.2.1, and 33.1. 7.1 This test method covers the determination of dissolved and total recoverable lead in most waters and wastewaters. 7.2 The test method is applicable in the range from 1.0 to 10 mg/L of lead. The upper limits of detectability can be increased to concentrations greater than 10 mg/L by dilution of the sample. 17.1 This test method covers the determination of dissolved and total recoverable lead in most waters and brines. 17.2 This test method is applicable in the range from 100 to 1000 μg/L of lead. The range may be extended upward by dilution of the samples. 27.1 This test method describes the determination of lead in water and waste waters using differential pulse anodic stripping voltammetry. 27.2 This test method is applicable up to a concentration of 100 μg/L lead. Higher concentrations can be determined by dilution. 27.3 The lower limit of detection for lead is 1.0 μg/L. Note 13—The lower limit of detection for differential pulse anodic stripping voltammetry is not absolute and can easily be lowered by changing the experimental parameters as described in Appendix X1. However, these variations have not been interlaboratory tested. 39.1 This test method covers the determination of dissolved and total recoverable lead in most waters and wastewaters. 39.2 The test method is applicable in the range from 5 to 100 μg/L of lead using a 20-μL injection. The range can be increased or decreased by varying the volume of sample injected or the instrumental settings. High concentrations may be diluted but preferably should be analyzed by direct aspiration atomic absorption spectrophotometry (Test Method A). 39.3 This test method has been used successfully with reagent water, lake water, river water, well water, filtered tap water, condensate from a medium Btu coal gasification process, waste treatment plant effluent, and a production plant process water. It is the user's responsibility to assure validity of this test method for untested matrices. |
||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Vorschriften verwenden?
Wir bieten Ihnen Lösungen, damit Sie immer nur die gültigen (aktuellen) legislativen Vorschriften verwenden könnten.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-23 (Zahl der Positionen: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.