Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop
Automatische name übersetzung:
Standard Test Method for Total Energy Auswirkungen der Kunststoff-Filme nach Dart-Tropfen
NORM herausgegeben am 1.4.2014
Bezeichnung normen: ASTM D4272-14
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.4.2014
SKU: NS-26635
Zahl der Seiten: 7
Gewicht ca.: 21 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
dart drop, energy to break, film, free-falling dart, impact, instrumented impact, total energy, ICS Number Code 83.140.10 (Films and sheets)
Significance and Use | ||||||||||||||||||
5.1 Evaluation of the impact toughness of film is important in predicting the performance of a material in applications such as packaging, construction, and other uses. The test simulates the action encountered in applications where moderate-velocity blunt impacts occur in relatively small areas of film. 5.2 The values obtained by this test method are highly dependent on the method and conditions of film fabrication as well as the type and grade of resin. 5.3 Test methods employing different missile velocities, impinging surface diameters, or effective specimen diameters will most likely produce different results. Data obtained by this test method cannot necessarily be compared directly with those obtained by other test methods. 5.4 The impact resistance of a film, while partly dependent on thickness, does not have a simple correlation with sample thickness. Hence, impact values expressed in joules (ft·lbf) normalized over a range of thickness will not necessarily be linear with thickness. Data from this test method are comparable only for specimens that vary by no more than ±15 % from the nominal or average thickness of the specimens tested. 5.5 The test results obtained by this test method are greatly influenced by the quality of film under test. The influence of variability of data obtained by this procedure will, therefore, depend strongly on the sample quality, uniformity of film thickness, the presence of die marks, contaminants, etc. 5.6 Several impact test methods are used for film. It is sometimes desirable to know the relationships among test results derived by different test methods. A study was conducted in which four films made from two resins (polypropylene and linear low-density polyethylene), with two film thicknesses for each resin, were impacted using Test Methods D1709 (Test Method A), Test Method D3420 (Procedures A and B), and Test Method D4272. The test results are shown in 1.1 This test method describes the determination of the total energy impact of plastic films by measuring the kinetic energy lost by a free-falling dart that passes through the film. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Terminology Relating to Plastics
|
|
Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
|
|
Standard Test Method for Pendulum Impact Resistance of Plastic Film
|
|
Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
|
ISO 7765–2
|
Plastics Film and Sheeting--Determination of Impact Resistance by the Free Falling Dart Method--Part 2: Instrumented Puncture Test
|
|
Standard Guide for Determination of Thickness of Plastic Film Test Specimens
|
|
Standard Specification for Standard Atmospheres for Conditioning and Testing Flexible Barrier Materials
|
|
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
|
|
Standard Practice for Conditioning Plastics for Testing |
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-21 (Zahl der Positionen: 2 206 478)
© Copyright 2024 NORMSERVIS s.r.o.