Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Guide for General Pavement Deflection Measurements
Name übersetzen
NORM herausgegeben am 1.11.2020
Bezeichnung normen: ASTM D4695-03(2020)
Ausgabedatum normen: 1.11.2020
SKU: NS-1009567
Zahl der Seiten: 7
Gewicht ca.: 21 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
Benkelman beam, deflection sensor, deflection surveys, falling-weight deflectometer (FWD), impulse deflection testing device, load cell, load/deflection testing, nondestructive testing (NDT), pavement surface deflection, pavement testing, sampling frequency, static deflection testing device, steady-state dynamic deflection testing device,, ICS Number Code 93.080.20 (Road construction materials)
Significance and Use | ||||||||||
5.1 NDT measurement of pavement surface deflections provides information that can be used for the structural evaluation of new or in-service pavements. These deflection measurements may be used to determine the following pavement characteristics: 5.1.1 Modulus of each layer. 5.1.2 Overall stiffness of the pavement system. 5.1.3 Load transfer efficiency of PCC pavement joints. 5.1.4 Modulus of subgrade reaction. 5.1.5 Effective thickness, structural number, or soil support value. 5.1.6 Bearing capacity or load carrying capacity of a pavement. 5.2 These parameters may be used for the analysis and design of reconstructed and rehabilitated flexible and rigid pavements, pavement structural adequacy assessment including joint efficiency of PCC pavement, void detection in PCC pavement, research, and/or network structural inventory purposes. |
||||||||||
1. Scope | ||||||||||
1.1 This guide provides procedural information for measuring pavement surface deflections, directly under, or at locations radially outward (offset) from a known static, steady-state, or impulse load. Deflections are measured with sensors that monitor the vertical movement of a pavement surface due to the load. This guide describes procedures for the deflection measurement using various deflection testing devices and provides the general information that should be obtained regardless of the type of testing device used. 1.2 This guide is applicable for deflection measurements performed on flexible asphalt concrete (AC), rigid portland cement concrete (PCC), or composite (AC/PCC) pavements. Rigid pavements may be plain, jointed, jointed reinforced, or continuously reinforced concrete. 1.3 The values stated in SI units are to be regarded as standard. Inch-pound units given in parentheses are for information purposes only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
2. Referenced Documents | ||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-24 (Zahl der Positionen: 2 206 712)
© Copyright 2024 NORMSERVIS s.r.o.