Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Water Mass per Unit Volume of Soil and Rock In-Place by the Neutron Depth Probe Method
Automatische name übersetzung:
Standard Test Method for Water Masse pro Volumeneinheit für Boden- und Fels In-Place durch die Neutronen Tiefe Sonde Methode
NORM herausgegeben am 15.6.2014
Bezeichnung normen: ASTM D5220-14
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 15.6.2014
SKU: NS-30328
Zahl der Seiten: 7
Gewicht ca.: 21 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
depth probe, in-place water content, in situ water content, neutron probe, nuclear methods, water mass per unit volume, ICS Number Code 13.080.40 (Hydrological properties of soil)
Significance and Use | ||||||||||||||||||||||||||
5.1 This test method is useful as a rapid, nondestructive technique for the calculation of the in-place water mass per unit volume of soil and rock at desired depths below the surface. 5.2 This test method is useful for informational and research purposes. It should only be used for quality control and acceptance testing when correlated to actual water mass per unit volume using procedures and methods described in 5.3 The non-destructive nature of this test method allows repetitive measurements to be made at a single test location for statistical analysis and to monitor changes over time. 5.4 The fundamental assumptions inherent in this test method are that the material under test is homogeneous and hydrogen present is in the form of water as defined by Test Method D2216. 1.1 This test method covers the
calculation of the water mass per unit volume of soil and rock by
thermalization or slowing of fast neutrons where the neutron source
and the thermal neutron detector are placed at the desired depth in
the bored hole lined by an access tube.
1.1.1 For limitations see Section 1.2 The water mass per unit volume, expressed as mass per unit volume of the material under test, is calculated by comparing the thermal neutron count rate with previously established calibration data (see Annex A1). 1.3 A precision statement has not been developed for this standard at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes unless correlated to other accepted ASTM methods. 1.4 Units—The values expressed in SI units are regarded as the standard. The inch-pound units given in parentheses may be approximate and are provided for information only. 1.5 All observed and calculated values shall conform to the guide for significant digits and rounding established in Practice D6026. 1.5.1 The procedures used to specify how data are collected, recorded, and calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. 1.6 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Test Method for Density of Soil
and Rock In-Place at Depths Below Surface by Nuclear Methods Standard Practice for Using Significant
Digits and Data Records in Geotechnical Data Standard Test Methods for In-Place
Density and Water Content of Soil and Soil-Aggregate by Nuclear
Methods (Shallow Depth) Standard Terminology Relating to Soil,
Rock, and Contained Fluids Standard Practice for Soil Exploration
and Sampling by Auger Borings Standard Test Methods for Crosshole
Seismic Testing (Withdrawn 2023) Standard Practice for Minimum
Requirements for Agencies Engaged in Testing and/or Inspection of
Soil and Rock as Used in Engineering Design and Construction Standard Practice for Thick Wall,
Ring-Lined, Split Barrel, Drive Sampling of Soils Standard Test Method for Density of Soil
in Place by the Drive-Cylinder Method (Includes all amendments and
changes 4/17/2018). Standard Test Methods for Laboratory
Determination of Water (Moisture) Content of Soil and Rock by
Mass Standard Practice for Rock Core Drilling
and Sampling of Rock for Site Exploration (Withdrawn 2023) Standard Practice for Thin-Walled Tube
Sampling of Soils for Geotechnical Purposes Standard Test Method for Standard
Penetration Test (SPT) and Split-Barrel Sampling of Soils |
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Vorschriften verwenden?
Wir bieten Ihnen Lösungen, damit Sie immer nur die gültigen (aktuellen) legislativen Vorschriften verwenden könnten.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-01 (Zahl der Positionen: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.