Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
Automatische name übersetzung:
Standardtestverfahren für Schlagfestigkeit von flachen, festen Kunststoffproben durch ein Sturm durch ein Fallgewicht Betroffene (Gardner Impact)
NORM herausgegeben am 1.7.2010
Bezeichnung normen: ASTM D5420-10
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.7.2010
SKU: NS-31108
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
dart impact, falling weight impact, Gardner impact, impact, impact resistance, mean-failure energy, mean-failure height, rigid plastic, Dart impact method, Failure end point--plastics, Falling weight test, Gardner impact test, Impact testing--plastics, Mean-failure energy/height/weight, Rigid plastics, Striker impact test, ICS Number Code 83.140.10 (Films and sheets)
Significance and Use | ||||||||||||||||||||||
Plastics are viscoelastic it is and therefore possible that they are sensitive to changes in velocity of weights falling on their surfaces. However, the velocity of a free-falling object is a function of the square root of the drop height. A change of a factor of two in the drop height will cause a change of only 1.4 in velocity. Hagan, et al (2) found that the mean-failure energy of sheeting was constant at drop heights between 0.30 and 1.4 m. Different materials respond differently to changes in the velocity of impact. The test conditions used in Geometry GA are the same as those used in Geometry FA of Test Method D5628 (see Table 1). The test conditions of Geometry GB are equivalent to the geometry used for the Gardner Variable Height Impact Test (3). The test conditions of Geometry GC cause a punch-shear type of failure because the support-plate hole is close to the diameter of the striker. The test conditions of Geometry GD are the same as those in Test Method D3763. The test conditions of Geometry GE are the same as those in Test Method D4226, impactor head configuration H.25. Because of the nature of impact testing, the selection of a test method and striker must be somewhat arbitrary. Consider the end use environment and requirements when choosing from the available striker geometries. However, the selection of any one of the striker geometries is permitted, after such consideration. Note 2—Material processing can have a significant affect on the development of a plastic's physical properties. Consult relevant material standards for processing guidelines |
||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||
1.1 This test method covers the determination of the relative ranking of materials according to the energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a striker impacted by a falling weight. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1—There is no similar or equivalent ISO standard. |
||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||
|
Historisch
1.4.2010
Historisch
1.2.2011
Historisch
1.12.2011
Historisch
15.2.2009
Historisch
1.7.2008
Historisch
1.8.2012
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.