Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Mass Per Unit Area of Pile Yarn Floor Coverings
Name übersetzen
NORM herausgegeben am 1.2.2020
Bezeichnung normen: ASTM D5848-20
Ausgabedatum normen: 1.2.2020
SKU: NS-994990
Zahl der Seiten: 13
Gewicht ca.: 39 g (0.09 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
carpet, construction, floor covering, mass per unit area, pile yarn,
Significance and Use | ||||||||||||||||||
4.1 The determination of the mass per unit area of pile yarn floor covering is useful in quality and cost control during the manufacture of pile floor covering. Both appearance and performance may be affected by changes in mass per unit area. 4.2 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and supplier should conduct comparison testing to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned to each laboratory for testing. The average results from the two laboratories should be compared using Student's 1.1 This test method covers the measurement of mass per unit area of machine-made woven, knitted, and tufted pile yarn floor covering both before and after an adhesive-back coating application. 1.2 This test method encompasses three techniques for determination of mass per unit area as applicable: 1.2.1 Section 7, for determining total mass per unit area, applies to both coated and uncoated (unfinished) pile floor coverings. 1.2.2 Section 8, for determining component mass per unit area, applies only to uncoated (unfinished) pile yarn floor coverings. 1.2.3 Section 9, for determining pile yarn mass per unit area, applies only to back-coated, or finished, pile yarn floor coverings. 1.3 Determination of mass per unit area of pile yarn floor coverings was previously contained within Test Methods D418. For user convenience, Subcommittee D13.21 subdivided Test Methods D418 into separate standards, of which this test method is one. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only (except where shown in 1.4.1) and are not considered standard. 1.4.1 The following sections are measured in SI units: Table 1, sections 9.8.4.2, 9.8.6.3 to 9.8.6.10, A2.1, A2.2, and A2.3. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 9.5. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-22 (Zahl der Positionen: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.