Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Practice for Installation of Geocomposite Pavement Drains
Name übersetzen
NORM herausgegeben am 1.5.2022
Bezeichnung normen: ASTM D6088-06(2022)
Ausgabedatum normen: 1.5.2022
SKU: NS-1056636
Zahl der Seiten: 9
Gewicht ca.: 27 g (0.06 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
backfill, “C”-ing, collector, conduit, drain positioning gate, edgedrain, geocomposites, geosynthetic, installation/placement boot, “J”-ing, joints, outlet pipe, outlet tees, trench, underdrain, wheel trencher,, ICS Number Code 93.080.20 (Road construction materials)
Significance and Use | ||||||||||||||||||||||
5.1?This practice is intended to provide installation guidance for designers, specifiers, installation contractors, regulatory agencies, owners, and inspectors who are involved in the planning and installation of geocomposite pavement edgedrains and underdrains. As with any standard practice, modification may be required for specific project conditions or for special local or regional conditions. Fig. 1 shows the proper horizontal alignment of the drain based on various trench conditions outlined in 9.2, and the vertical depth of placement of the drain needed for a geocomposite edge drain to function most effectively as both a collector and conduit. FIG. 1?Typical Type and Arrangement of Drain 5.2?Fig. 2 shows the typical type and arrangement of equipment used to install geocomposite highway edgedrains. The combination of these recommended installation conditions, techniques, and equipment are critical to the satisfactory long-term performance of these products. FIG. 2?Proper Horizontal Alignment Note 1:?Drain positioning gate should be located and adjusted
to position, and hold the geocomposite drain against the trench
wall, to prevent possible J-ing or C-ing of the drain during
backfilling and compaction.
|
||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||
1.1?This practice covers recommendations and identifies pertinent areas of consideration for the installation of buried geocomposite drains used for highway edgedrains, under-drains, or other pavement drainage applications meeting the requirements of Specification D7001. These recommendations are intended as guidelines for developing a satisfactory construction and installation method to minimize installation-caused deformation or damage and to provide long-term performance of these products. It is also intended as a guideline for ensuring a stable underground environment for these materials under a wide range of service conditions. Because of the numerous and diverse product designs available and the inherent variability of natural ground conditions, achieving satisfactory performance of any one product may require review by the engineer and modification to provisions contained herein to meet specific project requirements. 1.2?The scope of this practice necessarily excludes product performance criteria such as compressibility in any plane, flow capacity, inlet capacity, or geotextile selection and use. It is, therefore, incumbent upon the product manufacturer, specifier, and project engineer to verify that the product specified for an intended application, when installed according to procedures outlined in this practice, will provide satisfactory long-term performance according to criteria established by the owner for that application. A commentary of product performance and installation factors important in achieving a satisfactory installation is included in Appendix X1. 1.3?The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-23 (Zahl der Positionen: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.