Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Determining the Volume of Bulk Materials Using Contours or Cross Sections Created by Direct Operator Compilation Using Photogrammetric Procedures
Automatische name übersetzung:
Standard Test Methode zur Bestimmung der Volumen von Schüttgütern Mit Konturen oder Querschnitte Erstellt von Direct Operator Compilation Mit Photogrammetrische Verfahren
NORM herausgegeben am 1.9.2010
Bezeichnung normen: ASTM D6172-98(2010)
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.9.2010
SKU: NS-34091
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
aerial, inventory, photogrammetric, photography, stockpile, volume, Aerial analysis, Bulk materials, Coal/coke products, Contours, Cross section data/analysis, Horizontal testing, Inventory analysis/control, Photogrammetric methods, Stockpiles, Volumetric measurement, ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)
Significance and Use |
This test method audits the volume of material in a stockpile and is used with a density value to calculate a tonnage calculation value used to compare the book value to the physical inventory results. This test method is used to determine the volume of coal or other materials in a stockpile. |
1. Scope |
1.1 This test method covers procedures concerning site preparation, technical procedures, quality control, and equipment to direct the efforts for determining volumes of bulk material. These procedures include practical and accepted methods of volumetric determination. 1.2 This test method allows for only two volume computation methods. 1.2.1 Contour Test Method—See 8.1.1 and 9.1. 1.2.2 Cross-Section Test Method—See 8.1.2 and 9.2 1.2.3 This test method requires direct operator compilation for both contours and cross-section development. 1.2.4 The use of Digital Terrain Model software and procedures to create contours or cross sections for volume calculation is NOT encompassed in this test method. Note 1—A task group has been established to develop a test method for Digital Terrain Modeling (DTM) procedures. It will address all known data collection procedures such as conventional ground survey, photogrammetry, geodetic positioning satellite (GPS), and so forth. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system is used independently of the other. Combining values from the two systems can result in nonconformance with the specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
Historisch
1.12.2010
Historisch
1.11.2012
Historisch
1.11.2012
Historisch
1.11.2012
Historisch
1.2.2013
Historisch
1.10.2010
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-22 (Zahl der Positionen: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.