Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM D6797-15
Standard Test Method for Bursting Strength of Fabrics Constant-Rate-of-Extension (CRE) Ball Burst Test (Withdrawn 2024)
Automatische name übersetzung:
Standard Test Method for Berstfestigkeit von Gewebe mit konstanter Rate -of- Extension ( CRE) Ball Burst -Test
NORM herausgegeben am 1.7.2015
Informationen über die Norm:
Bezeichnung normen: ASTM D6797-15
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.7.2015
SKU: NS-614644
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM D6797-15 :
Keywords:
ball burst, bursting strength,, ICS Number Code 59.080.30 (Textile fabrics)
Ergänzende Informationen
| Significance and Use | ||||||||||||||
|
5.1 This method is used to determine the force required to rupture textile fabric by forcing a steel ball through the fabric with a constant-rate-of-extension tensile tester. 5.2 This is a new method and therefore the history of data is very small, however the agreement of within- laboratory data suggest this method may be considered for acceptance testing of commercial shipments with caution. 5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, samples used for such comparative test should be as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing, and randomly assigned in equal numbers to each laboratory. Other fabrics with established test values may also be used for these comparative tests. The test results from the laboratories involved should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected, or future test results for that fabric must be adjusted in consideration of the known bias. |
||||||||||||||
| 1. Scope | ||||||||||||||
|
1.1 This test method describes the measurement for bursting strength of woven and knitted textiles taken from rolls of fabric or fabric taken from garments. Note 1: For the measurement of bursting strength with a
hydraulic or pneumatic machine, refer to Test Method D3786. For the measurement of the
bursting strength by means of a ball burst mechanism, refer to Test
Method D3787
Note 2: Constant Rate of Traverse (CRT) machines and Constant
Rate of Extension (CRE) machines have been shown to provide
different results. When using a CRT device, refer to Test Method
D3787.
1.2 The values stated in either SI units or U.S. customary units are to be regarded as standard, but must be used independently of each other. The U.S. customary units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||
| 2. Referenced Documents | ||||||||||||||
|
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
