Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Categorization and Quantification of Airborne Fungal Structures in an Inertial Impaction Sample by Optical Microscopy
Automatische name übersetzung:
Standard Test Method for Kategorisierung und Quantifizierung von Airborne Pilzstrukturen in einem Trägheitsaufprall Probe durch optische Mikroskopie
NORM herausgegeben am 1.5.2009
Bezeichnung normen: ASTM D7391-09
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.5.2009
SKU: NS-38346
Zahl der Seiten: 12
Gewicht ca.: 36 g (0.08 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
fungal structures, spore, spores, mold, mould, fungal, bioaerosol, indoor air quality, fungi, fungus, impactor, impaction, ICS Number Code 07.100.99 (Other standards related to microbiology)
Significance and Use | ||
This test method is used to estimate and categorize the number and type of fungal structures present on an inertial impactor sample. Fungal structures are identified and quantified regardless of whether they would or would not grow in culture. It must be emphasized that the detector in this method is the analyst, and therefore results are subjective, depending on the experience, training, qualification, and mental and optical fatigue of the analyst. |
||
1. Scope | ||
1.1 This test method is a procedure that uses direct microscopy to analyze the deposit on an inertial impaction sample. 1.2 This test method describes procedures for categorizing and enumerating fungal structures by morphological type. Typically, categories may be as small as genus (for example, Cladosporium) or as large as phylum (for example, basidiospores). 1.3 This method contains two procedures for enumerating fungal structures: one for slit impaction samples and one for circular impaction samples. This test method is applicable for impaction air samples, for which a known volume of air (at a rate as recommended by the manufacturer) has been drawn, and is also applicable for blank impaction samples. 1.4 Enumeration results are presented in fungal structures/sample (fs/sample) and fungal structures/m3 (fs/m3). 1.5 The range of enumeration results that can be determined with this method depends on the size of the spores on the sample trace, the amount of particulate matter on the sample trace, the percentage of the sample trace counted, and the volume of air sampled. 1.6 This method addresses only the analysis of samples. The sampling process and interpretation of results is outside the scope of this method. 1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||
2. Referenced Documents | ||
|
Historisch
1.9.2012
Historisch
1.9.2012
Historisch
1.6.2014
Historisch
1.10.2009
Historisch
1.3.2009
Historisch
1.4.2008
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-08-25 (Zahl der Positionen: 2 344 896)
© Copyright 2024 NORMSERVIS s.r.o.