Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Practice for Manual Piston Cylinder Sampling for Volatile Crude Oils, Condensates, and Liquid Petroleum Products
Name übersetzen
NORM herausgegeben am 1.7.2022
Bezeichnung normen: ASTM D8009-22
Ausgabedatum normen: 1.7.2022
SKU: NS-1071000
Zahl der Seiten: 14
Gewicht ca.: 42 g (0.09 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
condensate sampling, crude oil sampling, high vapor pressure, live crude oil, manual piston cylinder, sampling,, ICS Number Code 75.080 (Petroleum products in general)
Significance and Use | ||||||||||||||||
5.1?This practice allows the collection of a representative sample of crude oil and/or condensate that may contain trace volatile dissolved components such as methane, ethane, propane, and fixed gases that would normally be lost using conventional atmospheric sampling methods. These highly volatile components can result in vapor pressure conditions above atmospheric pressure. This practice is recommended whenever accurate determination of vapor pressure, flash point, or other properties are required and where loss of volatile components can affect the test results. 5.2?This practice is intended for capturing samples of crude oil and/or condensate for testing for the purpose of classification for transportation of dangerous goods as UN Class 3 Flammable Liquids, but is not limited to classification testing. Other test methods with sensitivities to light end loss may also utilize this sampling practice. 5.3?Practice D3700 using a floating piston cylinder is recommended whenever true vapor pressures greater than 300 kPa at 50 ?C are anticipated. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1?This practice includes the equipment and procedures for obtaining a representative sample of live or high vapor pressure crude oils, condensates, and/or liquid petroleum products from low pressure sample points, where there is insufficient sample point pressure to use a Floating Piston Cylinder (FPC) as described in Practice D3700. 1.2?This practice is intended for use with sample types, such as UN Class 3 Flammable Liquids, that might have been collected and transported using open containers. The use of a manual piston cylinder in place of open containers is intended to prevent the loss of volatile (light end) components, which can impact subsequent test results. 1.3?This practice is suitable for sampling crude oils, condensates, and/or liquid petroleum products having true vapor pressures less than 300 kPa (43 psia nominal) at 50 ?C. This practice applies to samples that will typically fall between Practices D4057 (API MPMS Chapter 8.1) and D3700. This practice shall not be used for materials classified as UN Class 2 Gases2 (having a vapor pressure greater than 300 kPa at 50 ?C or is completely gaseous at 20 ?C at 101.3 kPa.). 1.4?This practice allows for sampling of crude oils that flow freely at the conditions of sampling. 1.5?It is the responsibility of the user to ensure that the sampling point is located so as to obtain a representative sample. 1.6?The values stated in SI units are to be regarded as standard. 1.6.1?ExceptionThe values given in parentheses are for information only. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-22 (Zahl der Positionen: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.