Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Practice for Acoustic Emission Examination of Reinforced Thermosetting Resin Pipe (RTRP)
Automatische name übersetzung:
Standard Praxis für Schallemissionsprüfung von verstärkten duroplastischen Harzrohr (RTRP)
NORM herausgegeben am 1.1.2011
Bezeichnung normen: ASTM E1118/E1118M-11
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.1.2011
SKU: NS-40498
Zahl der Seiten: 12
Gewicht ca.: 36 g (0.08 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
adhesive joints, Felicity effect, Felicity ratio, FRP pipe, load hold, RTRP, zone location, Acoustic emission (AE) testing--plastics, Adhesive joints, Calibration--acoustic emission analysis instrumentation, Carbon fiber reinforced pipe, Felicity effect/ratio, Fiberglass-reinforced plastics (FRP), Load hold, Noise level measurement, Piping systems, Plastic-lined ferrous metal pipe/fittings/flanges, Pressure testing--plastic pipe/tube, Reinforced thermosetting-resin pipe (RTRP), Resins
Significance and Use | ||||||||||||||||||||||||
The AE examination method detects damage in RTRP. The damage mechanisms detected in RTRP are as follows: resin cracking, fiber debonding, fiber pullout, fiber breakage, delamination, and bond or thread failure in assembled joints. Flaws in unstressed areas and flaws which are structurally insignificant will not generate AE. This practice is convenient for on-line use under operating conditions to determine structural integrity of in-service RTRP usually with minimal process disruption. Flaws located with AE should be examined by other techniques; for example, visual, ultrasound, and dye penetrant, and may be repaired and retested as appropriate. Repair procedure recommendations are outside the scope of this practice. |
||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||
1.1 This practice covers acoustic emission (AE) examination or monitoring of reinforced thermosetting resin pipe (RTRP) to determine structural integrity. It is applicable to lined or unlined pipe, fittings, joints, and piping systems. 1.2 This practice is applicable to pipe that is fabricated with fiberglass and carbon fiber reinforcements with reinforcing contents greater than 15 % by weight. The suitability of these procedures must be demonstrated before they are used for piping that is constructed with other reinforcing materials. 1.3 This practice is applicable to tests below pressures of 35 MPa absolute [5000 psia]. 1.4 This practice is limited to pipe up to and including 0.6 m [24 in.] in diameter. Larger diameter pipe can be examined with AE, however, the procedure is outside the scope of this practice. 1.5 This practice applies to examinations of new or in-service RTRP. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. For more specific safety precautionary information see 8.1. |
||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||
|
Historisch
1.11.2012
Historisch
1.8.2013
Historisch
1.7.2012
Historisch
1.11.2013
Historisch
1.8.2012
Historisch
1.4.2009
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.