Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments
Automatische name übersetzung:
Standard-Leitfaden zur Messung von einigen elektronischen Eigenschaften von Ultraschall-Prüfgeräte
NORM herausgegeben am 1.8.2011
Bezeichnung normen: ASTM E1324-11
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.8.2011
SKU: NS-41305
Zahl der Seiten: 11
Gewicht ca.: 33 g (0.07 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
electronic characteristics, evaluation, instruments, linearity, pulsers, receivers, ultrasonic: Battery voltage, Charge time, Current measurement, Electrical performance, Electronic measurement, Gate/alarm section, Horizontal linear motion, Noise and sensitivity, Performance--laboratory instrumentation/process, Power supply, Pulse-echo ultrasonic testing, Receiver section, Time base section, Time variable gain (TVG), Ultrasonic testing, Voltage, ICS Number Code 19.100 (Non-destructive testing)
Significance and Use | ||||||
The recommended measurement procedures described in this guide are intended to provide performance-related measurements that can be reproduced under the specified test conditions using commercially available test instrumentation. These measurements indicate capabilities of sections of the ultrasonic testing instrument independent of specific transducers or examination conditions. Measurements are made from normally available connectors or test points so that no access to internal circuitry is required. Further, this guide is not intended for service, calibration, or maintenance of circuitry for which the manufacturer's instructions are available. It is intended primarily for pulse echo flaw detection instruments operating in the nominal frequency range of 100 kHz to 25 MHz, but the procedures are applicable to measurements on instruments utilizing significantly higher frequency components. These procedures can be applied to the evaluation of any pulse-echo ultrasonic testing instrument which can be described as a combination of the electronic sections discussed in this guide. Note 2—These procedures are not intended to preclude the use or application of equipment for which some or all of the measurement techniques of this document are not applicable. An ultrasonic testing instrument that cannot be completely described as a combination of the electronic sections discussed in this practice can be partially evaluated. Each portion of the ultrasonic testing instrument that is evaluated must fit the description for the corresponding section. This guide is meant to be used by electronic personnel to evaluate the electronic system components and not the ultrasonic system characteristics. |
||||||
1. Scope | ||||||
1.1 This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments: 1.1.1 Power Supply Section: line regulation, 1.1.2 Pulser Section:
1.1.3 Receiver Section:
1.1.4 Time Base Section:
1.1.5 Gate/Alarm Section:
1.2 This guide complements Practice E317, and is not intended for evaluating the performance characteristics of ultrasonic testing instruments on the inspection/production line. Note 1—No access to internal circuitry is required. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^REFERENCE: ASTM Standards: D2548 Method of Test for Analysis of Oil Soluble Petroleum Sulfonates by Liquid Chromatography; Replaced by D 3712 (Withdrawn) E317 Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments E1316 Terminology for Nondestructive Examinations ISO Standard: ISO 10012 Measurement Management SystemsRequirements for Measurement Processes and Measuring Equipment ANSI Standard: Z540-1 General Requirements for Calibration Laboratories and Measurement and Test Equipment Other Standard: IEEE Std. 100, IEEE Standard Dictionary of Electrical and Electronics Terms |
||||||
2. Referenced Documents | ||||||
|
Historisch
15.6.2012
Historisch
1.11.2012
Historisch
15.6.2012
Historisch
1.6.2010
Historisch
1.11.2012
Historisch
1.6.2007
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.