Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Practice for Pressure Water Cleaning and Cutting
Automatische name übersetzung:
Standard Praxis für Druck-Wasser- Reinigung und Schneiden
NORM herausgegeben am 1.10.2008
Bezeichnung normen: ASTM E1575-08
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.10.2008
SKU: NS-42238
Zahl der Seiten: 10
Gewicht ca.: 30 g (0.07 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
abrasive blasting, cleaning, construction, cutting, demolition, hydrojetting, lancing, moleing, shotgunning, water blasting, Abrasive blasting, Cleaning, Construction, Cutting, Demolition, Fluid discharge, High-pressure water cutting, Hydrojetting, Lancing, Moleing, Personnel--safety, Pressure pump, Pumps, Shot gunning, Water blasting, ICS Number Code 25.100.01 (Cutting tools in general), 25.220.20 (Surface treatment)
1. Scope | ||
This practice is intended to provide guidance on the proper operation of pressure water-jet cleaning and cutting equipment. This practice is also applicable at lower pressures where there is foreseeable risk of injury. This practice is provided to assist persons unfamiliar with the operation of water-jet cleaning and cutting equipment in learning to correctly use the equipment. Correct operation and use of the pressure water-jet cleaning and cutting equipment is the responsibility of the operator and employer. After the operator has familiarized himself with the identification of pressure metal fittings, hoses, guns, and accessories in accordance with the original equipment manufacturer's specifications, instructions, and programmed instructional material, hydrojetting may begin. Modification of water-jetting equipment shall not be done without prior written approval by the manufacturer of the equipment. Employees shall be instructed in the recognition and avoidance of unsafe conditions. Note 2—Warning: Serious harm or injury may result from the misuse of water-jetting equipment and the use of improper fittings, hoses, or attachments. The use of pressure water-jet equipment for cutting and cleaning is a rapidly evolving technology. This practice will be periodically reviewed for any required changes at least every five years. ^SCOPE:1.1 This practice covers the personnel requirements, operator training, operating procedures, and recommended equipment performance/design for the proper operation of all types of pressure water-jet cleaning and cutting equipment as normally used by industries concerned with construction, maintenance, repair, cleaning, cutting, and demolition work. 1.2 The term high-pressure water jetting covers all water jetting, including the use of additives or abrasives at pressures above 100.5 psig (0.69 MPa). 1.3 Any person required to operate or maintain pressure water-jetting equipment shall have been trained and have demonstrated the ability and knowledge to do so in accordance with the original equipment manufacturer's instructions, specifications, and training programs. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Notes 1-8 and Sections 8 and 11 for specific hazards statements. |
||
2. Referenced Documents | ||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-07-18 (Zahl der Positionen: 2 337 971)
© Copyright 2024 NORMSERVIS s.r.o.