Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Friction Coefficient Measurements Between Tire and Pavement Using a Variable Slip Technique
Automatische name übersetzung:
Standard Test Method for Reibungskoeffizient Die Messungen zwischen Reifen und Straßen Mit einer Variable Schlickertechnik
NORM herausgegeben am 10.1.1997
Bezeichnung normen: ASTM E1859-97(2001)
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 10.1.1997
SKU: NS-43342
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
tire, ICS Number Code 83.160.01 (Tyres in general), 93.080.99 (Other standards related to road engineering)
1. Scope | ||||||||||||||||
1.1 This test method covers the measurement of the longitudinal friction coefficient with a measurement device that imposes braking-slip between a tire and a surface for the full range of braking-slip speed values. 1.2 This test method utilizes a series of incremental single measurements of friction force on a braked test wheel as it is pulled over a wetted or contaminated pavement surface. The rotational velocity of the braked wheel is feedback controlled in order to give a predetermined variable slip ratio gradient in accordance with set program parameters. The test wheel is kept under a constant static normal load and at a constant longitudinal speed of travel. Its major plane is perpendicular to the road plane and parallel to its direction of motion. 1.3 The values measured represent the friction properties obtained with the equipment and procedures stated in this test method and do not necessarily agree or correlate directly with those obtained by other pavement friction measuring methods. 1.4 The values are intended for use in: 1.4.1 Evaluating the braking friction forces on a pavement relative to that of other pavements. 1.4.2 Evaluating changes in the braking friction forces of a particular pavement with the passage of time. 1.4.3 Evaluating the changes in the braking friction force of a pavement when subjected to polishing wear and loss of macrotexture caused by traffic with passage of time. 1.4.4 Evaluating changes in the braking friction forces of a pavement contaminated with ice, moderate amounts of slush and snow, pollen, vehicle oil spills and condensates from vehicle engine exhaust, and deposits from other pollution sources. 1.4.5 Evaluating the braking friction forces of a specimen tire on a clean or contaminated pavement. 1.5 The friction values reported by this test method are insufficient to determine the distance required to stop a vehicle on either a dry, wet, or contaminated pavement. They are also insufficient for determining the speed at which control of a vehicle would be lost. 1.6 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6 and Note 4. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.