Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Methods for Tension Testing of Metallic Materials (Includes all amendments And changes 5/28/2015).
Automatische name übersetzung:
Standard-Prüfverfahren für Spann Prüfung metallischer Werkstoffe
NORM herausgegeben am 1.7.2013
Bezeichnung normen: ASTM E8/E8M-13a
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.7.2013
SKU: NS-48040
Zahl der Seiten: 28
Gewicht ca.: 84 g (0.19 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
accuracy, bending stress, discontinuous yielding, drop-of-the-beam, eccentric force application, elastic extension, elongation, extension-under-load, extensometer, force, free-running crosshead speed, gauge length, halt-of-the force, percent elongation, plastic extension, preload, rate of stressing, rate of straining, reduced section, reduction of area, sensitivity, strain, stress, taring, tensile strength, tension testing, yield point elongation, yield strength
Significance and Use | ||||||||||||||||||||||||||||
4.1 Tension tests provide information on the strength and ductility of materials under uniaxial tensile stresses. This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances. 4.2 The results of tension tests of specimens machined to standardized dimensions from selected portions of a part or material may not totally represent the strength and ductility properties of the entire end product or its in-service behavior in different environments. 4.3 These test methods are considered satisfactory for acceptance testing of commercial shipments. The test methods have been used extensively in the trade for this purpose. |
||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||
1.1 These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. 1.2 The gauge lengths for most round specimens are required to be 4D for E8 and 5D for E8M. The gauge length is the most significant difference between E8 and E8M test specimens. Test specimens made from powder metallurgy (P/M) materials are exempt from this requirement by industry-wide agreement to keep the pressing of the material to a specific projected area and density. 1.3 Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material. For examples, see Test Methods and Definitions A370 and Test Methods B557, and B557M. 1.4 Room temperature shall be considered to be 10 to 38°C [50 to 100°F] unless otherwise specified. 1.5 The values stated in SI units are to be regarded as separate from inch/pound units. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.