ASTM F1901-10
ASTM F2349-04(2010)..
ASTM F2536-06b(2011)..
ASTM F2769-10
ASTM F2805-11
ASTM F2984-13
Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM F1397-93(2012)
Standard Test Method for Determination of Moisture Contribution by Gas Distribution System Components
Automatische name übersetzung:
Standard Test Methode zur Bestimmung von Feuchtigkeit Beitrag von Systemkomponenten Gasverteilung
NORM herausgegeben am 1.7.2012
Informationen über die Norm:
Bezeichnung normen: ASTM F1397-93(2012)
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.7.2012
SKU: NS-50150
Zahl der Seiten: 11
Gewicht ca.: 33 g (0.07 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM F1397-93(2012) :
Keywords:
components, contamination, gas distribution, moisture analyzer, moisture contribution, semiconductor processing, water outgassing, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)
Ergänzende Informationen
| Significance and Use |
|
3.1 The purpose of this test method is to define a procedure for testing components being considered for installation into a high-purity gas distribution system. Application of this test method is expected to yield comparable data among components tested for the purposes of qualification for this installation. |
| 1. Scope |
|
1.1 This test method covers testing components for total moisture contribution to a gas distribution system at ambient temperature. In addition, the test method allows testing at elevated ambient temperatures as high as 70°C and of the component moisture capacity and recovery. 1.2 This test method applies to in-line components containing electronics grade materials such as those used in semiconductor gas distribution systems. 1.3 Limitations: 1.3.1 This test method is limited by the sensitivity of current instrumentation, as well as by the response time of the instrumentation. This test method is not intended to be used for test components larger than 12.7-mm (1/2-in.) outside diameter nominal size. This test method could be applied to larger components; however, the stated volumetric flow rate may not provide adequate mixing to ensure a representative sample. Higher flow rates may improve the mixing but excessively dilute the sample. 1.3.2 This test method is written with the assumption that the operator understands the use of the apparatus at a level equivalent to six months of experience. 1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 5. |
Ähnliche Normen:
Historisch
1.8.2010
Historisch
1.5.2010
Historisch
1.2.2011
Historisch
1.8.2010
Historisch
1.8.2011
Historisch
1.12.2013
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
