Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
Name übersetzen
NORM herausgegeben am 1.2.2023
Bezeichnung normen: ASTM F2145-23
Ausgabedatum normen: 1.2.2023
SKU: NS-1135827
Zahl der Seiten: 5
Gewicht ca.: 15 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) bodied mechanical fittings for use with outside diameter controlled PA 11 pipe, and nominal 2 pipe size (IPS) and smaller. In addition, it specifies general requirements of the material from which these fittings are made. Performance requirements shall include tests to determine elevated temperature sustained pressure, tensile strength, in-line fitting, mechanical saddle fittings, temperature cycling, and joint constant tensile load.
Keywords:
gas, mechanical saddle fitting, plastic mechanical fitting, Polyamide 11 pipe, Polyamide 12 pipe, rotation test, temperature cycling test,, ICS Number Code 23.040.45 (Plastic fittings)
1. Scope | ||||||||||||||||||||||||
1.1?This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) and Polyamide 12 (PA 12) bodied mechanical fittings for use with outside diameter controlled PA 11, nominal 2 pipe size (IPS), and smaller complying with Specification F2945, and PA 12, nominal 2 pipe size (IPS), and smaller complying with Specification F2785. In addition, it specifies general requirements of the material from which these fittings are made. 1.2?The test methods described in this specification are not intended to be used as routine quality tests. 1.3?This specification covers the types of mechanical fittings covered in 3.2.1. 1.4?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5?The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-23 (Zahl der Positionen: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.