ASTM F2619/F2619M-11

D1599-18

Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings

FED-STD-123G

Federal Standard Marking for Shipment (Civil Agencies)

Military Standard 129P

Standard Practice--Military Marking for Shipment and Storage

PPI TR-3

Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.

PPI TR-4

Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe

F1973-21

Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems

CSA Z662

Oil and Gas Pipeline Systems Available from Canadian Standards Association (CSA), 5060 Spectrum Way, Mississauga, ON L4W 5N6, Canada, http://www.csa.ca.

D2122-22

Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

D2683-20

Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

D4218-20

Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique

F1055-16a(2022)

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing (Includes all amendments and changes 11/8/2022).

F1473-23

Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins

F2206-19

Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)

CFR 49 Part 192

Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards Available from U.S. Department of Transportation, Transportation Safety Institute, Pipeline Safety Division, PO Box 25082, Oklahoma City, OK 73125-5050.

Federal Register Vol. 71,

No. 50, March 15, 2006

D2290-19a

Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).

D3261-24

Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

D3350-21

Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

D1600-18

Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

D1603-20

Standard Test Method for Carbon Black Content in Olefin Plastics

D2513-20

Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

D2837-22

Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

D638-22

Standard Test Method for Tensile Properties of Plastics

D1238-23a

Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).

F412-23

Standard Terminology Relating to Plastic Piping Systems

D1598-23

Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure