Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Qualifying Coatings for Use on F3125 Grade A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement
Name übersetzen
NORM herausgegeben am 1.4.2020
Bezeichnung normen: ASTM F2660-20
Ausgabedatum normen: 1.4.2020
SKU: NS-991842
Zahl der Seiten: 7
Gewicht ca.: 21 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
environmental hydrogen embrittlement, galvanic potential, high strength bolts, hydrogen embrittlement, open circuit potential, salt solution, threshold stress,, ICS Number Code 21.060.10 (Bolts, screws, studs)
Significance and Use | ||||||||||||||||||||||||||||||||||
4.1 This test method describes the testing procedure that shall be used to qualify a coating system that is under consideration for use on ASTM F3125 Grade A490 high strength structural bolts made of any steel composition permitted by the F3125 specification for Grade A490 bolts. The test method measures the susceptibility of coated specimen bolts to the influence of an externally applied potential (see 7.2.3.3) by testing for the threshold of embrittlement in a salt solution environment. |
||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||
1.1 This test method defines the procedures and tests to evaluate the effect of a coating system on the susceptibility to environmental hydrogen embrittlement (EHE) of an ASTM F3125 Grade A490 high strength structural bolt. 1.2 This test method shall qualify a coating system for use with any size of F3125 Grade A490 bolts (that is, 1/2 to 1-1/2 in.) high strength structural bolts, relative to EHE. 1.3 The characteristic to be evaluated by this test method is the susceptibility to EHE caused by hydrogen generated from corrosion protection of the steel bolt by sacrificial galvanic corrosion of the coating. Testing shall be performed on coated, specimen ASTM F3125 Grade A490 bolts manufactured to the maximum susceptible tensile strength values (see Table 1) of the bolt (see Section 5 Specimen Bolt Requirements). The internal hydrogen embrittlement (IHE) susceptibility will also be inherently evaluated when the EHE is tested through this test method. There is no need for a separate IHE susceptibility test. 1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-22 (Zahl der Positionen: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.