ASTM C1681-14
ASTM C564-14
ASTM C877M-02(2009)..
ASTM D1869-95(2010)..
ASTM D6396-99(2012)..
ASTM F1336-07
Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM F2946-12
Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes
Automatische name übersetzung:
Standard-Spezifikation für PVC-Hub und Elastomerdichtung (Dichtung) T-Anschluss für Verbindungskunststoffrohr zur Insitu Rohrleitungen und Schächte
NORM herausgegeben am 1.8.2012
Informationen über die Norm:
Bezeichnung normen: ASTM F2946-12
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.8.2012
SKU: NS-54770
Zahl der Seiten: 4
Gewicht ca.: 12 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM F2946-12 :
Keywords:
elastomeric seal, rubber gasket, service connection, sewer tap, watertight seal, ICS Number Code 23.040.80 (Seals for pipe and hose assemblies)
Ergänzende Informationen
| 1. Scope | ||||||||||||||||||||||||||||
|
1.1 This specification covers the minimum performance and material requirements for a three piece tee connector for connection between plastic pipe and insitu pipes, manholes and wastewater structures in sanitary and storm sewer applications. 1.1.1 The three piece seal system consists of a 4 through 30-in. PVC (polyvinyl chloride) hub pipe, an elastomeric seal (gasket) and a mechanical band (Fig. 1). The system is installed in either a bored or cast hole opening in the host pipe or structure to a specific dimension that corresponds to the combined diameter of the PVC pipe outside diameter/tolerance and the elastomeric seal thickness. FIG. 1 Three-Piece Sealing System
(Connector)
1.2 These tee connectors are designed to provide a non-pressure (gravity flow) watertight connection between the incoming pipe and an insitu pipe or manhole/structure to the limits defined in this standard. 1.3 The following precautionary
caveat pertains only to the test methods portion, Section
|
|
Standard Terminology Relating to Plastic Piping Systems
|
|
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
|
|
Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Includes all amendments and changes 10/8/2021).
|
|
Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
|
|
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
|
|
Standard Terminology Relating to Concrete Pipe and Related Products
|
|
Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
|
Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines
|
C900
|
Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 in. Through 12 in. (100 mm Through 300 mm), for Water Transmission and Distribution
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
|
|
Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air (Includes all amendments and changes 5/13/2020).
|
|
Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals |
Ähnliche Normen:
Historisch
1.6.2014
Historisch
1.5.2014
Historisch
1.10.2009
Historisch
1.6.2010
Historisch
1.10.2012
Historisch
1.5.2007
