Vorsicht!

In Ihrem Browser ist die Javascript-Aktivierung nicht erlaubt. Einige Funktionen mögen nicht richtig funktionieren. Für vollständige Funktionalität des Internet-Geschäfts empfehlen wir Javascript zu aktivieren. Siehe hier Instruktion, wie man im Ihren Web-Browser JavaScript aktiviert.

Angezeigte Währung: €

Preisanzeige: ohne MWS

Ergänzende Informationen

ASTM F2947-12

Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

Automatische name übersetzung:

Standard-Spezifikation für 150 bis 1500 mm [ 6 bis 60 in. ] Die ringförmige Wellenprofil - Wand Polyethylen (PE) Rohre und Fittings für Kanalisation Anwendungen

NORM herausgegeben am 1.5.2012

Sprache
Realisierung	PDF - sofortiges Download - 79.70 € Gedruckt - 79.70 €
Zugänglichkeit	AUF LAGER
Preis	79.70 € ohne MWS
79.70 €

Informationen über die Norm:

Bezeichnung normen: ASTM F2947-12
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.5.2012
SKU: NS-54771
Zahl der Seiten: 6
Gewicht ca.: 18 g (0.04 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM

Drucken

Einem Bekannten abschicken

Anfrage

Die Annotation des Normtextes ASTM F2947-12 :

Keywords:

corrugated HDPE pipe, fittings, interior liner, PE, pipe, polyethylene, profile wall, sanitary sewer, Corrugated pipe, Pipe fittings, Polyethylene (PE), Sewer, ICS Number Code 93.030 (External sewerage systems)

Ergänzende Informationen

1. Scope

1. Scope

1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 150 to 1500 mm [6 to 60 in.].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with an interior liner using a corrugated exterior profile (1.4 Units—The values stated in either SI or inch-pound units are to be regarded separately as standard. Within the text the Imperial (inch-pound) units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

LRFD, Section 12	AASHTO LRFD Bridge Design Specifications Section 12-Buried Structures and Tunnel Liners
F2136-18(2024)	Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F412-23	Standard Terminology Relating to Plastic Piping Systems
D6992-16(2023)	Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
D4703-16	Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
D4389-04	Standard Specification for Finished Glass Fabrics Woven From Rovings
D3212-21	Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D618-21	Standard Practice for Conditioning Plastics for Testing
D2990-17	Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Empfehlungen:

EEviZak – alle Gesetze einschließlich ihrer Evidenz in einer Stelle

Bereitstellung von aktuellen Informationen über legislative Vorschriften in der Sammlung der Gesetze bis zum Jahr 1945.
Aktualisierung 2x pro Monat!

Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.

Hier können Sie Ihre Cookie-Einstellungen nach Ihren Wünschen anpassen.

Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können.