Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Corrosion Testing of Products of Zirconium, Hafnium, and Their Alloys in Water at 680°F (360°C) or in Steam at 750°F (400°C) (Includes all amendments And changes 2/28/2019).
Automatische name übersetzung:
Standard Test Method for Korrosionsprüfung der Produkte von Zirkon, Hafnium und deren Legierungen in Wasser bei 680 ° F (360 ° C) oder in Dampf bei 750 ° F (400 ° C)
NORM herausgegeben am 1.9.2011
Bezeichnung normen: ASTM G2/G2M-06(2011)e1
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.9.2011
SKU: NS-57588
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Other non-ferrous metals and their alloysCorrosion of metals
Keywords:
mass gain, steam corrosion, water corrosion, ICS Number Code 77.060 (Corrosion of metals), 77.120.99 (Other non-ferrous metals and their alloys)
Significance and Use | ||||
This test method is primarily used as an acceptance test for products of zirconium, hafnium, and their alloys. This standard has been widely used in the development of new alloys, heat treating practices, and for evaluation of welding techniques. Specimens are normally tested after careful etching and rinsing. Specimens with as-manufactured surfaces may also be tested without further surface removal. When tubing with a second material clad on the inner surface is to be tested, the inner cladding shall be removed prior to the test. |
||||
1. Scope | ||||
1.1 This test method covers (1) the determination of mass gain, and (2) the surface inspection of products of zirconium, hafnium, and their alloys when corrosion tested in water at 680°F [360°C] or in steam at 750°F [400°C]. 1.2 This test method is to be utilized in its entirety to the extent specified herein as a product acceptance test. 1.3 This test method may be used on wrought products, castings, powder metallurgy products, and weld metals. 1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9. |
||||
2. Referenced Documents | ||||
|
Historisch
1.5.2012
Historisch
1.5.2012
Historisch
1.5.2012
Historisch
1.5.2012
Historisch
1.5.2013
Historisch
1.10.2010
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-12-23 (Zahl der Positionen: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.