Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
Name übersetzen
NORM herausgegeben am 1.7.2022
Bezeichnung normen: ASTM D1709-22
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.7.2022
SKU: NS-1067849
Zahl der Seiten: 9
Gewicht ca.: 27 g (0.06 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
drop dart, impact, plastic film,, ICS Number Code 83.140.10 (Films and sheets)
Significance and Use | ||||||||||||||||||
4.1?Test Methods A and B are used to establish the weight of the dart when 50 % of the specimens fail under the conditions specified. Data obtained by one test method cannot be compared directly with the other test method nor with those obtained from tests employing different conditions of missile velocity, impinging surface diameter, effective specimen diameter, material construction and finish of the dart head, and film thickness. The values obtained by these test variables are highly dependent on the method of film fabrication. 4.2?The results obtained by Test Methods A and B are greatly influenced by the quality of film under test. The confidence limits of data obtained by this procedure can, therefore, vary significantly, depending on the sample quality, uniformity of film gage, die marks, contaminants, etc. 4.3?Test Methods A and B have been found useful for specification purposes. Note 4:?With sufficient data, correlation between test results
and field performance can usually be established.
4.4?The impact resistance of plastic film, while partly dependent on thickness, has no simple correlation with sample thickness. Hence, impact values cannot be normalized over a range of thickness without producing misleading data as to the actual impact resistance of the material. Data from these test methods are comparable only for specimens that vary by no more than ?25 % from the nominal or average thickness of the specimens tested. 4.5?Several impact test methods are used for film. It is sometimes desirable to know the relationships among test results derived by different test methods. A study was conducted in which four films made from two resins (polypropylene and linear low-density polyethylene), with two film thicknesses for each resin, were impacted using Test Methods D1709 (Method A), D3420 (Procedures A and B), and D4272. The test results are shown in the Appendix. Differences in results between Test Methods D1709 and D4272 are not unusual since Test Methods D1709 represents failure initiated energy, while Test Method D4272 is initiation plus completion energy. Some films exhibit consistency when the initiation energy is the same as the total energy. This statement and the test data also appear in the significance sections and appendixes of Test Methods D3420 and D4272. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1?These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart. This energy is expressed in terms of the weight (mass) of the missile falling from a specified height which would result in 50 % failure of specimens tested. 1.2?Two test methods are described: 1.2.1?Test Method A employs a dart with a 38.10 ? 0.13-mm (1.500 ? 0.005-in.) diameter hemispherical head dropped from a height of 0.66 ? 0.01 m (26.0 ? 0.4 in.). This test method can be used for films whose impact resistances require masses of about 50 g to about 6 kg to fracture them. 1.2.2?Test Method B employs a dart with a 50.80 ? 0.13-mm (2.000 ? 0.005-in.) diameter hemispherical head dropped from a height of 1.52 ? 0.03 m (60.0 + 0.25, ?1.70 in.). Its range of applicability is from about 0.3 kg to about 6 kg. 1.3?Two testing techniques are described: 1.3.1?The standard technique is the staircase method. By this technique, the missile weight employed during the test is decreased or increased by uniform increments after the testing of each specimen, depending upon the result (fail or not fail) observed for the specimen. 1.3.2?The alternative technique provides for testing specimens in successive groups of ten. One missile weight is employed for each group and the missile weight is varied in uniform increments from group to group. 1.3.3?The staircase technique and the alternative technique give equivalent results both as to the values of impact failure weight which are obtained and as to the precisions with which they are determined. 1.4?The values stated in SI units are to be regarded as standard. The values stated in parentheses are for information only. Note 1:?Tests on materials that do not break, for any reason,
are not considered to be valid. It has been noted that certain
materials may stretch so far as to bottom out at the base of
certain test instruments without actually rupturing. Subcommittee
D20.19 is currently considering methods for testing these
materials. Anyone interested in participating in a Task Group
should contact the Chairman of Subcommittee D20.19 through ASTM
International Headquarters.
1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2:?Film has been arbitrarily defined as sheeting having
nominal thickness not greater than 0.25 mm (0.010 in.).
Note 3:?This test method is technically equivalent to ISO
7765-1:1988, with the exception of a larger tolerance on the drop
height in Test Method B, smaller tolerances on the dart diameters
for Test Methods A and B, and the requirement for a vented dart
well in 5.1.1. Also, the ISO
method does not allow the alternative testing technique described
in Section 11 of this test
method.
1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-01 (Zahl der Positionen: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.