Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
Automatische name übersetzung:
Standard Praxis zur Herstellung von Probekörpern von Asphalt-stabilisierten Böden
NORM herausgegeben am 1.1.2012
Bezeichnung normen: ASTM D4223/D4223M-12
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.1.2012
SKU: NS-26487
Zahl der Seiten: 5
Gewicht ca.: 15 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Earthworks. Excavations. Foundation construction. Underground works
Keywords:
asphalt-stabilization, soil stabilization, specimen preparation, test specimens, ICS Number Code 93.020 (Earth works. Excavations. Foundation construction. Underground works)
Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||
This practice is intended for the preparation of standard specimens of soil-asphalt mixtures suitable for tests of Test Methods , D1560, D1561, D4123, and other tests using specimens of the above dimensions. This practice is limited to only fine-grained soils as defined in 6.1. Note 1—The quality of the results produced by this practice is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing, sampling, inspection, and so forth. Users of this practice are cautioned that compliance with Practice D3740 does not in itself ensure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors. |
||||||||||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
1.1 This practice covers the selection and proportioning of soils and emulsified or cutback asphalts and the fabrication of 100-mm [4-in.] diameter by 65-mm [2.5-in.] high test specimens. 1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.3 Units—The values stated in either SI units or inch-pound units [presented in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight) while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F=ma) calculations are involved. 1.3.2 It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit for mass. However, the use of balances or scales recording pounds of mass (lbm) or recording in lbm/ft3 shall not be regarded as nonconformance with this standard. 1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^REFERENCE: ASTM Standards: C117 Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates D8 Terminology Relating to Materials for Roads and Pavements D75 Practice for Sampling Aggregates D653 Terminology Relating to Soil, Rock, and Contained Fluids D977 Specification for Emulsified Asphalt D1074 Test Method for Compressive Strength of Bituminous Mixtures D1188 Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples D1559 Test Method for Resistance to Plastic Flow of Bituminous Mixtures Using Marshall Apparatus (Withdrawn) D1560 Test Methods for Resistance to Deformation and Cohesion of Bituminous Mixtures by Means of Hveem Apparatus D1561 Practice for Preparation of Bituminous Mixture Test Specimens by Means of California Kneading Compactor D2026 Specification for Cutback Asphalt (Slow-Curing Type) D2027 Specification for Cutback Asphalt (Medium-Curing Type) D2028 Specification for Cutback Asphalt (Rapid-Curing Type) D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass D2397 Specification for Cationic Emulsified Asphalt D2419 Test Method for Sand Equivalent Value of Soils and Fine Aggregate D2726 Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction D4123 Test Method for Indirect Tension Test for Resilient Modulus of Bituminous Mixtures (Withdrawn) D4318 Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils D6026 Practice for Using Significant Digits in Geotechnical Data |
||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Historisch
1.1.2008
Historisch
1.2.2014
Historisch
1.2.2008
Historisch
1.2.2006
Historisch
1.2.2006
Historisch
15.1.2010
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.