ASTM E2688-10
ASTM E2748-12a
ASTM E2785-14
ASTM E662-14
ASTM E681-09
ASTM F1514-03(2013)..
Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM D5048-14
Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
Automatische name übersetzung:
Standard Test Methode zur Messung der Vergleichsbrenneigenschaften und Widerstand gegen Durchbrennen Solide Plastics Mit einem 125-mm-Flamme
NORM herausgegeben am 1.5.2014
Informationen über die Norm:
Bezeichnung normen: ASTM D5048-14
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.5.2014
SKU: NS-29628
Zahl der Seiten: 7
Gewicht ca.: 21 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Ignitability and burning behaviour of materials and productsPlastics in general
Die Annotation des Normtextes ASTM D5048-14 :
Keywords:
burning characteristics, flammability, plastics, solid, resistance to burn-through, small-scale burning tests, vertical burning tests, ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products), 83.080.01 (Plastics in general)
Ergänzende Informationen
| Significance and Use | ||||||||||||||
|
5.1 The test results represent afterflame plus afterglow time, in seconds, for a material under the conditions of the test. The test results for plaques also indicate whether or not the specified flame will burn through a material. 5.2 The effect of material thickness, colors, additives, deterioration, and possible loss of volatile components is measurable. 5.3 The burning characteristics vary with thickness. Compare test data with data for materials of similar thickness only. 5.4 The results serve as a reference for comparing the relative performance of materials and can be an aid in material selection. 5.5 In this test method, the specimens are subjected to specific laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it will not always be possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method. |
||||||||||||||
| 1. Scope | ||||||||||||||
|
1.1 This fire-test-response test method covers a small-scale laboratory procedure for determining the relative burning characteristics and the resistance to burn-through of plastics using small bar and plaque specimens exposed to a 125-mm (500-W nominal) flame. 1.2 This test method was developed
for polymeric materials used for parts in devices and appliances.
The results are intended to serve as a preliminary indication of
their acceptability with respect to flammability for a particular
application. The final acceptance of the material is dependent upon
its use in complete equipment that conforms with the standards
applicable to such equipment.
1.3 The classification system described in 1.4 If found to be appropriate, it is suitable to apply the requirements to other nonmetallic materials. Such application is outside the scope of this technical committee. 1.5 This test method is not intended to cover plastics when used as materials for building construction or finishing. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. 1.8 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Terminology Relating to
Plastics Standard Test Method for Measuring the
Comparative Burning Characteristics of Solid Plastics in a Vertical
Position (Includes all amendments and changes 9/11/2020). Standard Specification for Laboratory
Burner Used for Small-Scale Burning Tests on Plastic Materials
(Includes all amendments and changes 4/16/2020). Standard Practice for Confirmation of
20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning
Tests on Plastic Materials Standard Terminology of Fire
Standards Standard Practice for Conducting an
Interlaboratory Study to Determine the Precision of a Test
Method IEC?60695-11-20 Fire Hazard Testing-Part 11-20: Test
Flames - 500 W Flame Test Methods |
Ähnliche Normen:
Historisch
1.1.2010
Historisch
1.11.2012
Historisch
1.5.2014
Historisch
1.8.2014
Historisch
1.10.2009
Historisch
1.5.2013
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
