Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Determining the Relative Density (Specific Gravity) and Absorption of Fine Aggregates Using Infrared (Withdrawn 2022)
Automatische name übersetzung:
Standard Test Methode zur Bestimmung der relativen Dichte (spezifisches Gewicht) und Absorption der bildenden Aggregate Mit Infrarot-
NORM herausgegeben am 1.6.2014
Bezeichnung normen: ASTM D7172-14
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.6.2014
SKU: NS-37762
Zahl der Seiten: 5
Gewicht ca.: 15 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
absorption, aggregate, apparent density, apparent relative density, infrared, relative density, specific gravity, ICS Number Code 91.100.30 (Concrete and concrete products)
Significance and Use | ||||||||||||||||||||||||
4.1 Bulk relative density (specific gravity) is the characteristic generally used for calculation of the volume occupied by the aggregate in various mixtures containing aggregate including Portland cement concrete, bituminous concrete, and other mixtures that are proportioned or analyzed on an absolute volume basis. Bulk relative density (specific gravity) is used in the computation of voids in aggregate in C1252 and C29/C29M. Bulk relative density (specific gravity) determined on the saturated surface dry (SSD) basis is used if the aggregate is wet, that is, if its absorption has been satisfied. Conversely, the bulk relative density (specific gravity) determined on the oven-dry basis is used for computations when the aggregate is dry or assumed to be dry. 4.2 Apparent relative density (specific gravity) pertains to the relative density of the solid material making up the constituent particles not including the pore space within the particles that is accessible to water. This value is not widely used in construction aggregate technology. 4.3 Water absorption values are used to calculate the change in the mass of an aggregate due to water absorbed in the pore spaces within the constituent particles, compared to the dry condition, when it is deemed that the aggregate has been in contact with water long enough to satisfy most of the absorption potential. The laboratory standard for absorption is that obtained after submerging dry aggregate for approximately 24 hours in water. Aggregates mined from below the water table may have a higher absorption when used, if not allowed to dry. Conversely, some aggregates when used may contain an amount of absorbed moisture less than the 24 hours soaked condition: For an aggregate that has been in contact with water and that had free moisture on the particle surface, the percentage of free moisture can be determined by deducting the absorption from the total moisture content determined according to C566 by drying. |
||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||
1.1 This test method covers the determination of the relative density (specific gravity) and absorption of fine aggregates. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||
|
Historisch
1.6.2010
Historisch
1.6.2013
Historisch
1.12.2013
Historisch
1.7.2013
Historisch
1.6.2006
Historisch
1.5.2010
Bereitstellung von aktuellen Informationen über legislative Vorschriften in der Sammlung der Gesetze bis zum Jahr 1945.
Aktualisierung 2x pro Monat!
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-11-22 (Zahl der Positionen: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.